TOSHIBA TECRA 8000

Date: septembre 21st, 2013

Pour télécharger les drivers pour TOSHIBA TECRA 8000 pour Windows, Non-OS, Windows XP, Windows 98, Windows 95, Other, Windows 2000, Windows NT, Other, cliquez sur "Télécharger". Si vous avez besoin d'un drivers d'une autre version, envoyez une demande de driver. Si vous avez des questions sur ce driver, veuillez nous contacter via le formulaire de contact. Sur cette page, vous pouvez discuter notamment de l'installation, la désinstallation et la mise à jour du driver.

Modèle:
8000
Editeur:
Toshiba
Type de périphérique:
Portables, netbooks / Tecra
Licence:
Gratuit

Windows Non-OS

Windows

Type de fichier: BIOS
Version: 8.00
Taille: 653.77 Kb
Système d'exploitation: Windows XP
ACPI Flash BIOS version 8.00 for Tecra 8000.
View Change History
Type de fichier: BIOS
Version: 8.10
Taille: 657.41 Kb
Système d'exploitation: Windows XP
ACPI Flash BIOS version 8.10 for Tecra 8000.

View Change History

Type de fichier: BIOS
Version: 8.20
Taille: 658.24 Kb
Système d'exploitation: Windows XP
ACPI Flash BIOS version 8.20 for Tecra 8000.

CHANGE HISTORY

Version 8.20  07-14-1999

  • Corrected a problem that in "Display Auto Off Mode" in DOS mode. Turning ON the display from the "Display Off" state, caused an all white display.
  • Corrected in problem that "Wake-up on LAN" did not work running Windows '98, 2nd edition.
  • Corrected a problem that "Wake-up on LAN" did not work with "Password=Not Registered" in Setup, caused the computer to re-start under "Instant Security" state.
  • This BIOS is intended for Tecra 8000 models with processor speeds less than 500MHz. FDD problems are likely to occur when using this BIOS with 500MHz models.
Type de fichier: BIOS
Version: 8.50
Taille: 658.72 Kb
Système d'exploitation: Windows XP
ACPI Flash BIOS version 8.50 for Tecra 8000. 500MHz models ONLY.

CHANGE POINTS

Version 8.50  11-03-1999

  • This BIOS is for Tecra 8000 models equipped with the 500MHz Pentium only. A change was made to allow the fan to run at all times. This will prevent any overheating conditions should the computer hang and become unable to otherwise control heat.

Full change history is contained within the README file included in this download.

Type de fichier: BIOS
Version: 9.00
Taille: 660.7 Kb
Système d'exploitation: Windows XP
ACPI Flash BIOS version 9.00 for Tecra 8000. This is the initial Windows 2000 BIOS release for this model.

CHANGE HISTORY

Version 9.00  02-07-2000

  • BIOS for Pentium II and Pentium III models were intergrated.
  • A change was made to support Windows 2000.
  • The System BIOS was changed so that heat control of the fan would be done by using Watch Dog timer function of EC. (If EC doesn't support Watchdog Timer, for those with EC version 1.50 and lower, the heat control method used is unchanged. The fan always rotates on models that use a CPU of 500MHz and higher. For others, fan rotation is controlled, based on CPU temperature.
  • A change was made so that two ATAPI devices could be supported.
  • Corrected a problem with the Eject Password. The problem occurred when the Eject Password was set to Enable, and the computer was docked to the Desk Station. After shutdown, when running Windows 98, and then pressing the eject switch on the Desk Station, the system didn't ask for a password.
  • Corrected a problem where, after pre-installing Windows 95/98, execting hibernation without shutting down the computer, resulted in an intermittent hibernation error.
Type de fichier: BIOS
Version: 9.10
Taille: 661.11 Kb
Système d'exploitation: Windows XP
ACPI Flash BIOS version 9.10 for Tecra 8000.

CHANGE HISTORY

Version 9.10  06-30-2000

  • Power management controlling power consumption and tempurature has been improved.

Version 9.00  02-07-2000

  • BIOS for Pentium II and Pentium III models were intergrated.
  • A change was made to support Windows 2000.
  • The System BIOS was changed so that heat control of the fan would be done by using Watch Dog timer function of EC. (If EC doesn't support Watchdog Timer, for those with EC version 1.50 and lower, the heat control method used is unchanged. The fan always rotates on models that use a CPU of 500MHz and higher. For others, fan rotation is controlled, based on CPU temperature.
  • A change was made so that two ATAPI devices could be supported.
  • Corrected a problem with the Eject Password. The problem occurred when the Eject Password was set to Enable, and the computer was docked to the Desk Station. After shutdown, when running Windows 98, and then pressing the eject switch on the Desk Station, the system didn't ask for a password.
  • Corrected a problem where, after pre-installing Windows 95/98, execting hibernation without shutting down the computer, resulted in an intermittent hibernation error.

Version 8.50  11-03-1999

  • This BIOS is for Tecra 8000 models equipped with the 500MHz Pentium only. A change was made to allow the fan to run at all times. This will prevent any overheating conditions should the computer hang and is unable to otherwise control heat.

Version 8.20  07-14-1999

  • Corrected a problem that in "Display Auto Off Mode" in DOS mode. Turning ON the display from the "Display Off" state, caused an all white display.
  • Corrected in problem that "Wake-up on LAN" did not work running Windows '98, 2nd edition.
  • Corrected a problem that "Wake-up on LAN" did not work with "Password=Not Registered" in Setup, caused the computer to re-start under "Instant Security" state.
  • This BIOS is intended for Tecra 8000 models with processor speeds less than 500MHz. FDD problems are likely when using this BIOS with 500MHz models.

Version 8.10  06-04-1999

  • BIOS support for CPU with clock speed of 400MHz.
  • Correct a problem that, when running Windows 95/98, with "Legacy USB" enabled, and a USB mouse attached, the computer would hang when suspend or resume was executed.
  • Corrected a problem that, when the computer went into hibernation, running Windows 95, and a USB mouse was attached, the computer would hang coming out of hibernation.
  • Corrected a problem that, when the computer was running in "Low Processor Speed", and the FN F5 keys were used to switch between displays, there would be a very long pause.
  • Corrected a resume failure problem when running Windows 98. When the computer is suspended and the Select Bay lock has been put into the unlocked position; a warning message will appear when the the computer is powered on. When the Select Bay lock is then moved to the locked position, the computer will display experience a resume failure.
  • Corrected a problem that, when "USB Legacy = Enabled" was set in BIOS Setup, and using a USB keyboard, the " character key did not work.

Version 8.00  03-01-1999

  • Corrected a problem in Windows '98 with a hang when operating under ACPI mode. C3 state function was disabled completely.

Version 7.91  01-11-1999

  • Corrected a problem where, under Win98 with the Processing Speed set to low, the system with a CPU module (Dixon 333MHz) can hang.
  • Corrected a problem where, if a SCSI card is connected under Win98, suspending and waking the system resulted in a system hang.
  • Corrected a problem where, after setting the display resolution to 1024X768 16M colors, if booting the system with a CRT disconnected, there would be no image on the LCD.
  • Corrected a problem where, in the case of resuming, the system would hang.

Version 7.90  12-14-1998

  • Corrected a problem where, when the Deskstation V Plus is connected with a PCI card (IBM Auto Wake Token Ring Card 4/16 (EH10)) and starting Win95, "!" appears in the Secondary IDE Controller section of Device Manager.
  • Corrected a problem where, if an Eject password is registered under Win98, the capability existed to undock a system without entering a password by unchecking "Enable Password Prompt".
  • Corrected a problem where, under Windows 98, the system could hang during hibernation suspend. Note: This and later versions of BIOS must be used in conjunction with video driver V4.10.01.5200-T2.00.04-02C or later.
  • Corrected a problem where the system would hang in the middle of the shutdown process if shutting down the system using the power switch under Win98 with the display off.
  • Corrected a problem where, after suspending the system under Win98 and opening or closing the lid while the system is off and then resuming the system, the result would be a resume failure.
  • Corrected a problem where suspending or resuming the system under Win95 or Win98 would lead to an all white or all black LCD.

Version 7.80  12-03-1998

  • Corrected a problem where the image on the LCD would disappear if the system is hot-docked or hot-undocked under multi-monitor mode.
  • Corrected a problem of an improper color setting when using Test & Diagnostic to set the screen to 320x200 (mode 0Dh).
  • Corrected a problem where, under Win98 ACPI mode, the system would hang when changing the processor to C3 state.
  • Corrected a problem where, in the System Setup menu (TSETUP), if the Home key is being held down for a short period of time, then the whole display would become black.
  • Corrected a problem where the system password will be disabled even when an incorrect password service diskette is used.
  • Corrected a problem where, under Win98, if the Eject Password is enabled, the Desk Station 5 Plus cannot be recognized by the system if the system is restarted after an incorrect Eject Password is input three times.

Version 7.70  10-30-1998

  • Corrected to resolve an issue where, under Windows 98, the mouse pointer would disappear after a suspend/resume event if the pointer was pointing to the start menu.
  • Corrected an issue where hot-undocking would fail under Windows 98 if the LAN Docker ethernet controller is disabled in Device Manager, and the system had been cold-booted in the Docker.
  • Corrected to fix hot-swapping problems with the SelectBay FDD.

Version 7.60  09-01-1998

  • Corrected to eliminate the possibility of a system shutdown if the CPU module's ambient air temperature had not reached the shutdown limit.
  • The VGA BIOS was updated for enhanced performance at 1024x768x24bpp.
  • Support was added for LS-120 in the SelectBay.
  • Updated to improve support for Libretto style (PCMCIA) FDD when docked.
  • Corrected a problem where if the system was set to Cardbus/16-bit mode, it would hang while booting with an R2 card (such as a modem) present.
  • Added a temperature parameter as a countermeasure against heat problems for the DVD model.
  • Eliminated the noise from the coil on the CPU during CPU throttling.
  • Added a warning message when an illegal update is done for the Japanese domestic model.

Version 7.50  08-17-1998

  • Corrected a problem where a reset signal to the modem controller was not generated causing a system hang under resume mode.
  • Corrected a problem where, under Windows NT with the AC adapter disconnected during display auto-off, the display will turn on.

Version 7.40  07-25-1998

  • Corrected a problem where the system would hang under Windows 98 while utilizing the hibernation function.

Version 7.30  07-17-1998

  • Initial Production BIOS for Tecra 8000
Type de fichier: BIOS
Version: 9.20
Taille: 670.01 Kb
Système d'exploitation: Windows XP
ACPI Flash BIOS version 9.20 for Tecra 8000.

CHANGE HISTORY

Version 9.20  03-02-2001

  • A problem resuming the computer was corrected. The computer, when running Windows 2000, took about 2 minutes to resume from Hibernation when the CD-ROM, Teac CD-224E-B30, (ZA2055P04) was connected to the Selectable Bay.

Version 9.10  06-30-2000

  • Power management controlling power consumption and tempurature has been improved.

Version 9.00  02-07-2000

  • BIOS for Pentium II and Pentium III models were intergrated.
  • A change was made to support Windows 2000.
  • The System BIOS was changed so that heat control of the fan would be done by using Watch Dog timer function of EC. (If EC doesn't support Watchdog Timer, for those with EC version 1.50 and lower, the heat control method used is unchanged. The fan always rotates on models that use a CPU of 500MHz and higher. For others, fan rotation is controlled, based on CPU temperature.
  • A change was made so that two ATAPI devices could be supported.
  • Corrected a problem with the Eject Password. The problem occurred when the Eject Password was set to Enable, and the computer was docked to the Desk Station. After shutdown, when running Windows 98, and then pressing the eject switch on the Desk Station, the system didn't ask for a password.
  • Corrected a problem where, after pre-installing Windows 95/98, execting hibernation without shutting down the computer, resulted in an intermittent hibernation error.

Version 8.50  11-03-1999

  • This BIOS is for Tecra 8000 models equipped with the 500MHz Pentium only. A change was made to allow the fan to run at all times. This will prevent any overheating conditions should the computer hang and is unable to otherwise control heat.

Version 8.20  07-14-1999

  • Corrected a problem that in "Display Auto Off Mode" in DOS mode. Turning ON the display from the "Display Off" state, caused an all white display.
  • Corrected in problem that "Wake-up on LAN" did not work running Windows '98, 2nd edition.
  • Corrected a problem that "Wake-up on LAN" did not work with "Password=Not Registered" in Setup, caused the computer to re-start under "Instant Security" state.
  • This BIOS is intended for Tecra 8000 models with processor speeds less than 500MHz. FDD problems are likely when using this BIOS with 500MHz models.

Version 8.10  06-04-1999

  • BIOS support for CPU with clock speed of 400MHz.
  • Correct a problem that, when running Windows 95/98, with "Legacy USB" enabled, and a USB mouse attached, the computer would hang when suspend or resume was executed.
  • Corrected a problem that, when the computer went into hibernation, running Windows 95, and a USB mouse was attached, the computer would hang coming out of hibernation.
  • Corrected a problem that, when the computer was running in "Low Processor Speed", and the FN F5 keys were used to switch between displays, there would be a very long pause.
  • Corrected a resume failure problem when running Windows 98. When the computer is suspended and the Select Bay lock has been put into the unlocked position; a warning message will appear when the the computer is powered on. When the Select Bay lock is then moved to the locked position, the computer will display experience a resume failure.
  • Corrected a problem that, when "USB Legacy = Enabled" was set in BIOS Setup, and using a USB keyboard, the " character key did not work.

Version 8.00  03-01-1999

  • Corrected a problem in Windows '98 with a hang when operating under ACPI mode. C3 state function was disabled completely.

Version 7.91  01-11-1999

  • Corrected a problem where, under Win98 with the Processing Speed set to low, the system with a CPU module (Dixon 333MHz) can hang.
  • Corrected a problem where, if a SCSI card is connected under Win98, suspending and waking the system resulted in a system hang.
  • Corrected a problem where, after setting the display resolution to 1024X768 16M colors, if booting the system with a CRT disconnected, there would be no image on the LCD.
  • Corrected a problem where, in the case of resuming, the system would hang.

Version 7.90  12-14-1998

  • Corrected a problem where, when the Deskstation V Plus is connected with a PCI card (IBM Auto Wake Token Ring Card 4/16 (EH10)) and starting Win95, "!" appears in the Secondary IDE Controller section of Device Manager.
  • Corrected a problem where, if an Eject password is registered under Win98, the capability existed to undock a system without entering a password by unchecking "Enable Password Prompt".
  • Corrected a problem where, under Windows 98, the system could hang during hibernation suspend. Note: This and later versions of BIOS must be used in conjunction with video driver V4.10.01.5200-T2.00.04-02C or later.
  • Corrected a problem where the system would hang in the middle of the shutdown process if shutting down the system using the power switch under Win98 with the display off.
  • Corrected a problem where, after suspending the system under Win98 and opening or closing the lid while the system is off and then resuming the system, the result would be a resume failure.
  • Corrected a problem where suspending or resuming the system under Win95 or Win98 would lead to an all white or all black LCD.

Version 7.80  12-03-1998

  • Corrected a problem where the image on the LCD would disappear if the system is hot-docked or hot-undocked under multi-monitor mode.
  • Corrected a problem of an improper color setting when using Test & Diagnostic to set the screen to 320x200 (mode 0Dh).
  • Corrected a problem where, under Win98 ACPI mode, the system would hang when changing the processor to C3 state.
  • Corrected a problem where, in the System Setup menu (TSETUP), if the Home key is being held down for a short period of time, then the whole display would become black.
  • Corrected a problem where the system password will be disabled even when an incorrect password service diskette is used.
  • Corrected a problem where, under Win98, if the Eject Password is enabled, the Desk Station 5 Plus cannot be recognized by the system if the system is restarted after an incorrect Eject Password is input three times.

Version 7.70  10-30-1998

  • Corrected to resolve an issue where, under Windows 98, the mouse pointer would disappear after a suspend/resume event if the pointer was pointing to the start menu.
  • Corrected an issue where hot-undocking would fail under Windows 98 if the LAN Docker ethernet controller is disabled in Device Manager, and the system had been cold-booted in the Docker.
  • Corrected to fix hot-swapping problems with the SelectBay FDD.

Version 7.60  09-01-1998

  • Corrected to eliminate the possibility of a system shutdown if the CPU module's ambient air temperature had not reached the shutdown limit.
  • The VGA BIOS was updated for enhanced performance at 1024x768x24bpp.
  • Support was added for LS-120 in the SelectBay.
  • Updated to improve support for Libretto style (PCMCIA) FDD when docked.
  • Corrected a problem where if the system was set to Cardbus/16-bit mode, it would hang while booting with an R2 card (such as a modem) present.
  • Added a temperature parameter as a countermeasure against heat problems for the DVD model.
  • Eliminated the noise from the coil on the CPU during CPU throttling.
  • Added a warning message when an illegal update is done for the Japanese domestic model.

Version 7.50  08-17-1998

  • Corrected a problem where a reset signal to the modem controller was not generated causing a system hang under resume mode.
  • Corrected a problem where, under Windows NT with the AC adapter disconnected during display auto-off, the display will turn on.

Version 7.40  07-25-1998

  • Corrected a problem where the system would hang under Windows 98 while utilizing the hibernation function.

Version 7.30  07-17-1998

  • Initial Production BIOS for Tecra 8000
Type de fichier: BIOS
Version: 9.30
Taille: 670.51 Kb
Système d'exploitation: Windows XP

CHANGE HISTORY

Version 9.30 ?07-26-2001

  • A change was made to correct a problem that some PC cards with a single spec for 16 bit and 3.3VDC may malfunction.

Version 9.20 ?03-02-2001

  • A problem resuming the computer was corrected. The computer, when running Windows 2000, took about 2 minutes to resume from Hibernation when the CD-ROM, Teac CD-224E-B30, (ZA2055P04) was connected to the Selectable Bay.

Version 9.10 ?06-30-2000

  • Power management controlling power consumption and tempurature has been improved.

Version 9.00 ?02-07-2000

  • BIOS for Pentium II and Pentium III models were intergrated.
  • A change was made to support Windows 2000.
  • The System BIOS was changed so that heat control of the fan would be done by using Watch Dog timer function of EC. (If EC doesn't support Watchdog Timer, for those with EC version 1.50 and lower, the heat control method used is unchanged. The fan always rotates on models that use a CPU of 500MHz and higher. For others, fan rotation is controlled, based on CPU temperature.
  • A change was made so that two ATAPI devices could be supported.
  • Corrected a problem with the Eject Password. The problem occurred when the Eject Password was set to Enable, and the computer was docked to the Desk Station. After shutdown, when running Windows 98, and then pressing the eject switch on the Desk Station, the system didn't ask for a password.
  • Corrected a problem where, after pre-installing Windows 95/98, execting hibernation without shutting down the computer, resulted in an intermittent hibernation error.

Version 8.50 ?11-03-1999

  • This BIOS is for Tecra 8000 models equipped with the 500MHz Pentium only. A change was made to allow the fan to run at all times. This will prevent any overheating conditions should the computer hang and is unable to otherwise control heat.
Type de fichier: Driver
Version: 1.41-RC2.
Taille: 546.5 Kb
Système d'exploitation: Windows 98
Type de fichier: Driver
Taille: 932.38 Kb
Système d'exploitation: Windows 95, Other, Windows NT
Toshiba AMD PCSCSI driver diskette V3.10 for Desk Station V and V Plus. Includes drivers for MS-DOS, Windows (95, NT, 3.x) and OS/2 Warp 3. Also includes DOS partitioner support for SCSI HDDs over 1GB. WinZip self-extracting Zip file creates driver diskette and displays README file when run under Windows. Also self-extracts under MS-DOS.
Type de fichier: Driver
Version: 1.02.1.
Taille: 36.19 Kb
Système d'exploitation: Windows 98, Windows 95, Other, Windows NT
Toshiba DMI Asset tag Utility (DOS) version 1.02.1. Allowsthe user to store a asset tag data string in the system management area of CMOS.
Type de fichier: Applicazione
Version: 1.02
Taille: 29 Kb
Système d'exploitation: Windows 98
Type de fichier: Applicazione
Version: 1.00.
Taille: 609.88 Kb
Système d'exploitation: Windows 2000
Type de fichier: Applicazione
Version: 1.10-RC1.
Taille: 682.5 Kb
Système d'exploitation: Windows 98, Windows 95, Windows NT
Toshiba Mobile Information Center Client (Win9x/NT) version 1.10-RC1.

This application, in conjunction with the server component, extends CA Unicenter functionality to dynamically discover Toshiba notebooks and gather information about notebook connectivity profiles.

Type de fichier: Driver
Version: 1.10
Taille: 749 Kb
Système d'exploitation: Windows 95
15.5.0.43.6.e32_wCAT
Type de fichier: Applicazione
Taille: 867 Kb
Système d'exploitation: Windows 98, Windows 95, Windows NT
Intel LAN Desk Client Manager 3.3 Patch for Win9x/NT. Updates LDCM v3.3 to better support Wake/Alert on LAN functions.
Type de fichier: Driver
Version: 3.8USRC2.
Taille: 748 Kb
Système d'exploitation: Windows 98
This package has to be installed after the audio driver is installed.
Type de fichier: Driver
Version: 1.2B2.
Taille: 2.78 Mb
Système d'exploitation: Windows NT
APM subsystems and other components in support of Windows NT 4.0 Service Packs 4 and 5. The self-installer automatically detects the machine and installs the appropriate updates.

This release updates the APM subsystem to v2.03.10-RC2 to eliminate FDD problems when upgrading previous versions of APM.

Type de fichier: Applicazione
Version: 2.4.3
Taille: 721 Kb
Système d'exploitation: Windows NT
Version: 8.0.0.140.0.x32_wCAT
Type de fichier: Driver
Version: 2.05.20.
Taille: 974.5 Kb
Système d'exploitation: Windows NT

Changes from previous version (p702apmn.exe)

  1. Fixed the issue that power management property does not open with Windows NT4.0 SP3.
  2. Modified the i8042 port driver to decrease the occurrences of the crazy mouse phenomenon.
  3. Bug fix:The AccuPoint cannot be used, after the PC was undocked from Docker.
  4. Supports Battery Meter
  5. Bug fix: Power Save icon doesn't reflect changes between Battery and External Power.
Type de fichier: Driver
Version: 4.11.01.5207-Q2.07.0
Taille: 834.13 Kb
Système d'exploitation: Windows 98
Windows 98 Display Driver version 4.11.01.5207-Q2.07.04-02-RC6 for NeoMagic 2200 (256AV) display adapters. This release updates the unattended installation script to properly overwrite the necessary driver files if they already exist.

This version updates the unattended installation script to fix a problem where DVD would not play after upgrading from a previous version.

Type de fichier: Driver
Version: 4.11.01.5207-Q2.07.0
Taille: 644 Kb
Système d'exploitation: Windows 95
This release corrects a screen corruption problem when the "Scrolling Marquee" screen saver is enabled at display resolution is 1024x768 True Color (24-bit).
Type de fichier: Driver
Version: 4.20Q
Taille: 236.5 Kb
Système d'exploitation: Windows NT
Type de fichier: Driver
Version: 1.0-RC2
Taille: 93.5 Kb
Système d'exploitation: Windows NT

Change History

  • Version 1.70 - 2012-09-12
    • Implemented the Intel specification to improve stability - updated MEBX to 7.0.0.0063.
    • EC/KBC V1.30: Improved standby stability.
    • EC/KBC V1.30: Modified the power supply error detection method.
    Version 1.50 - 2012-02-13
    • Added a boot LOGO sequence for ZAT (GPS) models.
    • Improved: Control of TPM on Intel TXT enabled systems.
    • Implemented a fix for an issue where the BIOS password cannot be entered when configured as follows: 1. Wired USB keyboard is connected to the port replicator. Wireless USB mouse is connected to a computer USB port. 3. Computer is docked to the port replicator.
    • Implemented a fix for an issue where the BIOS password can't be entered with some USB keyboards.
    Version 1.40 - 2011-11-15
    • Improved: Control of the TPM on Intel TXT enabled systems.
    Version 1.30 - 2011-10-27
    • Initial production BIOS for these models.
Type de fichier: Applicazione
Version: 2.04
Taille: 716.12 Kb
Système d'exploitation: Windows XP, Windows 98, Windows 95, Windows 2000, Windows NT
System Management Server (SMS) Connection is an asset management tool that creates a machine information file on each bootup which can then be read by LAN administrators.
Type de fichier: Applicazione
Version: 1.1-RC2
Taille: 38.5 Kb
Système d'exploitation: Windows 98, Windows 95
This is a MS-DOS utility that is used to manage (create, recreate) the Toshiba hibernation file.
Type de fichier: Driver
Version: 1.0B2
Taille: 152.5 Kb
Système d'exploitation: Windows 95
Type de fichier: Applicazione
Version: 1.8
Taille: 616 Kb
Système d'exploitation: Windows NT
Toshiba Windows NT Docking service version 1.8 for Portege 7020.

This release fixes a problem where "Eject PC" doesn't appear on the Start menu after a "warm dock" event.

Type de fichier: Applicazione
Version: 5.0
Taille: 594.5 Kb
Système d'exploitation: Windows 98, Windows 95
Toshiba Hibernation Utility version 5.0 for Windows 95/98. Updated to support Win98 SE.
Type de fichier: Applicazione
Version: 1.2-RC2
Taille: 41 Kb
Système d'exploitation: Windows 95
This is an Intel Management Engine (ME) Firmware update.

Change Points

  1. Improves or enables playback of specific media formats.

Install Instructions

  1. Save the downloaded file to the Windows Desktop.
  2. Save all work in progress and close open applications.
  3. Connect the AC Adapter.
  4. On the Windows Desktop, double-click the downloaded file to start the installation.
  5. Click Yes to continue if a User Account Control window is displayed.
  6. Click Execute the update.
  7. Reboot the computer.

Version Verification

The Intel ME Firmware (FW) version can not be verified on all computers. We recommend trying to install the firmware a second time. The program will advise if the firmware needs to be updated, or if the update is unnecessary.
Type de fichier: Driver
Version: 1.10E
Taille: 512.5 Kb
Système d'exploitation: Windows NT
Type de fichier: Driver
Version: 1.00
Taille: 298.13 Kb
Système d'exploitation: Windows 98, Windows 95
Docker Internal LAN driver version 1.00
Type de fichier: Driver
Version: 4.00SP4-RC2
Taille: 289.66 Kb
Système d'exploitation: Windows NT

This release adds support for unattended installation to the downloadable package when executed with the /auto switch.

Type de fichier: Applicazione
Version: 1.1
Taille: 30 Kb
Système d'exploitation: Windows 95
Type de fichier: Driver
Version: 4.06.2343.VCN-RC2
Taille: 1.66 Mb
Système d'exploitation: Windows 98, Windows 95
Windows 95/98 Sound driver version 4.06.2343.VCN-RC2 for Yamaha OPL3-SAx sound systems. This release fixes a GPF when repeatedly opening and closing AVI files.
Type de fichier: Driver
Version: 4.00.3322
Taille: 231.5 Kb
Système d'exploitation: Windows NT
Windows NT Sound Driver version 4.00.3322 for Yamaha OPL3-SAx Sound in Tecra 8000, Portege 7000.
Type de fichier: Driver
Version: 1.3
Taille: 523.5 Kb
Système d'exploitation: Windows NT
Type de fichier: Driver
Version: 4.10.1343.01-RC5
Taille: 671.14 Kb
Système d'exploitation: Windows 95
Type de fichier: Driver
Version: 1.0
Taille: 962 Kb
Système d'exploitation: Windows 95
This package has to be installed after Conexant audio driver is installed.
Type de fichier: Driver
Version: W9580004USB1-RC2
Taille: 2.01 Mb
Système d'exploitation: Windows 95
Toshiba Windows 95 Utilities version W9580004USB1-RC2 for Tecra 8000. This version fixes a possible memory leak in previous versions, and adds an unattended installer.

This version also supports unattended installation using the /auto switch

t8kutl95 /auto

Type de fichier: Driver
Version: W988004USB1-RC2
Taille: 1.99 Mb
Système d'exploitation: Windows 98
Toshiba Windows 98 Utilities version W988004USB1-RC2 for Tecra 8000. Fixes possible memory leak in previous versions, and provides an unattended installer.

This version also supports unattended installation using the /auto switch.

t8kutl98 /auto

Type de fichier: Applicazione
Version: 0.9.98.0611
Taille: 45 Kb
Système d'exploitation: Windows 98, Windows 95
Neomagic 32-bit Video Port Manager version 0.9.98.0611 for Win95/98 on Portege 7000 and Tecra 8000.
Type de fichier: Driver
Version: 2.0USB1
Taille: 655 Kb
Système d'exploitation: Windows 98, Windows 95, Windows 2000, Windows NT
This driver exposes system information to DMI-enabled applications.
Type de fichier: Applicazione
Version: 2.1USB2-RC2.
Taille: 881.35 Kb
Système d'exploitation: Windows 98, Windows 95, Windows 2000, Windows NT
Windows 9x, NT, 2000 TBIOS driver version 2.1USB2-RC2. TBIOS provides an interface for DMI-enabled applications to read data from the system's DMI data areas.
Type de fichier: Applicazione
Version: 2.4.6
Taille: 663.5 Kb
Système d'exploitation: Windows 98, Windows 95
Toshiba Mouse Control version 2.4.6 for Windows 95/98 on Portege 7000, Satellite 4000, Tecra 8000.
Type de fichier: Applicazione
Version: 2.4.7
Taille: 663 Kb
Système d'exploitation: Windows 98, Windows 95
Toshiba Mouse Control version 2.4.7 for Windows 95/98 on Tecra 8000.
Type de fichier: Applicazione
Version: 2.5.2
Taille: 665.5 Kb
Système d'exploitation: Windows 98, Windows 95
Toshiba Mouse Control (drivers) version 2.5.2 for Windows 95/98.
Type de fichier: Driver
Version: 1.00.04
Taille: 1.02 Mb
Système d'exploitation: Windows 2000
This package has to be installed after Conexant audio driver is installed.
Type de fichier: Applicazione
Version: 1.0 build 60303
Taille: 1.07 Mb
Système d'exploitation: Windows XP
This Utility will eliminate the "Wrong machine" messages when you try to restore the factory software image from the Config Builder CD or PIRAD CD/DVD. Click for more information about this issue.

Requires either a bootable diskette drive (FDD), or bootable CD-ROM (CD-RW, DVD-ROM/RW). If no FDD is available, requires access to CD authoring (burning) software and hardware.

Build 60303 fixes an issue where Satellite 5205-S705 units were programmed with the incorrect DMI model string.

Type de fichier: Applicazione
Version: 1.0.1.
Taille: 548.5 Kb
Système d'exploitation: Windows 98, Windows 95
This software is an optional system component that displays system LED icons for Toshiba notebook computers.
Type de fichier: Driver
Version: 1.0.1.
Taille: 574 Kb
Système d'exploitation: Windows NT
Type de fichier: BIOS
Taille: 1.09 Kb
Système d'exploitation: Windows XP
Toshiba CMOS Setup program for portable computers.

This DOS program displays and allows you to set the CMOS/BIOS settings of your Toshiba portable computer. This program does not run in a DOS session under Windows. From Windows, you'll need to restart in MS-DOS mode in order to use this utility.

You can also access the BIOS/CMOS setup screen without having to use TSETUP by holding down the [Esc] key when you first power-on the system.

Type de fichier: Driver
Version: 5.56-MR556ALL005
Taille: 3.6 Mb
Système d'exploitation: Windows 95
This is a TOSHIBA Media Controller Plug-in update.


Change Points

  1. Eliminates the following error after updating the Adobe Flash Player to version 11.2.202.235: "The Adobe Flash Player installed on your PC is not supported by TOSHIBA Media Controller Plug-in. TOSHIBA Media Controller Plug-in failed to start.
    This error occurs when attempting to forward movie play back to an external display.

Install Instructions

  1. Save the downloaded file to the Windows Desktop.
  2. Save all work in progress and close open applications.
  3. On the Windows Desktop, double-click the downloaded file to start the installation.
  4. Click Start when the TOSHIBA Archive Extractor window is displayed.
  5. Click Yes to continue if a User Account Control window is displayed.
  6. Click Next at the TOSHIBA Media Controller Plug-in InstallShield Wizard.
  7. Click Install to start the installation.
  8. Click Finish to complete the installation.

Version Verification

  1. Click Start, type Add or Remove Programs, then press Enter.
  2. Verify that the TOSHIBA Media Controller Plug-in application is version 1.0.8.0.
Type de fichier: Driver
Version: 5.56-MR556BALL01-RC2
Taille: 3.6 Mb
Système d'exploitation: Windows 98
Type de fichier: Driver
Version: MR577ALL003
Taille: 723.91 Kb
Système d'exploitation: Windows NT
Type de fichier: Driver
Version: 1.1.0.
Taille: 1.35 Mb
Système d'exploitation: Windows 2000
Provides Toshiba-specific Win2k display (LCD) power management functionality. Requires Toshiba ACPI common modules (TVALD).

Version 1.0.0 contained code which controlled portions of the display adapter as well as the display panel. This version (1.1.0) controls only the display panel.

Type de fichier: Applicazione
Version: 1.00.04
Taille: 1.25 Mb
Système d'exploitation: Windows 2000
This software is the foundation for the other Toshiba-provided Win2k Utilities, and must be installed first.
Type de fichier: Driver
Version: 1.00.01
Taille: 1.29 Mb
Système d'exploitation: Windows 2000
Type de fichier: Applicazione
Version: 1.0
Taille: 597.5 Kb
Système d'exploitation: Windows NT
Type de fichier: Applicazione
Version: 3.19x
Taille: 4.02 Mb
Système d'exploitation: Windows NT

PC DIAGNOSTIC TOOL

This utility can display the basic information of a computer and diagnose its built-in devices. However, assume that the diagnostic is for reference only. This product performs a diagnostic based on "Diagnostic Method for Main Components and Its Results." Therefore, hardware that is diagnosed as normal still may not actually be usable. When using this product, use the computer on which it is preinstalled or to which it is attached.

To open the PC Diagnostic Tool utility:

  1. Click the Start menu.
  2. Enter "Diagnostic" into the search field.
  3. Click "PC Diagnostic Tool" in the search results.
  4. The PC Diagnostic Tool will open showing basic computer information.
  5. Click the "Diagnostic Tool" tab to open the diagnostic portion of the utility.
  6. Select the items you want to run diagnostics for and click "Start Diagnostic".
  7. The PC Diagnostic Tool will run checks on the selected components and report back.
Type de fichier: Driver
Version: 2.21.
Taille: 48.84 Kb
Système d'exploitation: Windows 2000
Type de fichier: Driver
Version: 1.02.03-RC3.
Taille: 1.5 Mb
Système d'exploitation: Windows 2000

Non-OS

Type de fichier: BIOS
Version: 8.00
Taille: 653.77 Kb
Système d'exploitation: Other
Type de fichier: BIOS
Version: 8.10
Taille: 657.41 Kb
Système d'exploitation: Other
Type de fichier: BIOS
Version: 8.20
Taille: 658.24 Kb
Système d'exploitation: Other
Type de fichier: BIOS
Version: 8.50
Taille: 658.72 Kb
Système d'exploitation: Other
Type de fichier: BIOS
Version: 9.00
Taille: 660.7 Kb
Système d'exploitation: Other
Type de fichier: BIOS
Version: 9.10
Taille: 661.11 Kb
Système d'exploitation: Other
Type de fichier: BIOS
Version: 9.20
Taille: 670.01 Kb
Système d'exploitation: Other
Type de fichier: BIOS
Version: 9.30
Taille: 670.51 Kb
Système d'exploitation: Other
Type de fichier: Applicazione
Version: 1.0 build 60303
Taille: 1.07 Mb
Système d'exploitation: Other
Type de fichier: BIOS
Taille: 1.09 Kb
Système d'exploitation: Other


Connexe

TOSHIBA TECRA 8200
Pilotes pour Portables, netbooks TOSHIBA TECRA 8200 (Other)

TOSHIBA TECRA 8100
Pilotes pour Portables, netbooks TOSHIBA TECRA 8100 (Other)

TOSHIBA TECRA 530CDT
Pilotes pour Portables, netbooks TOSHIBA TECRA 530CDT (Other)

TOSHIBA TECRA 500CDT
Pilotes pour Portables, netbooks TOSHIBA TECRA 500CDT (Other)

TOSHIBA TECRA 700CT
Pilotes pour Portables, netbooks TOSHIBA TECRA 700CT (Other)

TOSHIBA TECRA 730XCDT
Pilotes pour Portables, netbooks TOSHIBA TECRA 730XCDT (Other)


Demande de driver

ejemplo